HomeStore

Panel Mount 10K Dual Log Potentiometer (10K Dual Log)

Product image 1
Product image 2
Product image 3

Panel Mount 10K Dual Log Potentiometer (10K Dual Log)

This Panel Mount 10K Dual Log Potentiometer is a dual-ganged potentiometer that will satisfy all your stereo-signal needs. Instead of just one potentiometer, you actually get two separate pots, 'ganged' together. Turning the grippy shaft twists both standard logarithmic-taper 10Kohm potentiometers. It's smooth and easy to turn, but not so loose that it will shift on its own. We also offer this potentiometer in a singular configuration.

Potentiometers, or "pots" to electronics enthusiasts, are differentiated by how quickly their resistance changes. In linear pots, the amount of resistance changes in a direct pattern. If you turn or slide it halfway, its resistance will be halfway between its minimum and maximum settings. That's ideal for controlling lights or a fan, but not necessarily for audio controls. Volume controls have to cater to the human ear, which isn't linear. Instead, logarithmic pots like this one increase their resistance on a curve. At the halfway point volume will still be moderate, but it will increase sharply as you keep turning up the volume. This corresponds to how the human ear hears. Using a log pot therefore gives the effect that a setting of full volume on the control sounds twice as loud as a setting of half volume. A linear pot used as a volume control would give large apparent changes in loudness at low volume settings, with little apparent change over the rest of the control´s range.

Unlike some of our other potentiometers, this one is not breadboard-friendly. The pins are about 0.2" apart so it will fit into a breadboard, but the two rows are close together so you'd short the two halves. Thus, we suggest soldering wires to the pins as necessary, using these in a perf-board that doesn't have the rows connected, or designing a custom PCB.

Once you're done prototyping, you can drill a hole into your project box and mount the potentiometer using the included washer and hex nut. We've got plenty of matching T18-splined knobs that you can pair up.

Technical Details

  • 10K ohm potentiometer, log taper
  • 100,000 Cycle Life
  • 16mm Body
  • Rotational travel: 300°
  • Static Stop Strength: 90 oz-in
  • Rotational Torque: 0.5 to 1.25 oz-in

Product Dimensions: 26.5mm x 25.0mm x 17.0mm / 1.0" x 1.0" x 0.7"

Product Weight: 7.5g / 0.3oz

$0.52

Original: $1.50

-65%
Panel Mount 10K Dual Log Potentiometer (10K Dual Log)

$1.50

$0.52

Product Information

Shipping & Returns

Description

This Panel Mount 10K Dual Log Potentiometer is a dual-ganged potentiometer that will satisfy all your stereo-signal needs. Instead of just one potentiometer, you actually get two separate pots, 'ganged' together. Turning the grippy shaft twists both standard logarithmic-taper 10Kohm potentiometers. It's smooth and easy to turn, but not so loose that it will shift on its own. We also offer this potentiometer in a singular configuration.

Potentiometers, or "pots" to electronics enthusiasts, are differentiated by how quickly their resistance changes. In linear pots, the amount of resistance changes in a direct pattern. If you turn or slide it halfway, its resistance will be halfway between its minimum and maximum settings. That's ideal for controlling lights or a fan, but not necessarily for audio controls. Volume controls have to cater to the human ear, which isn't linear. Instead, logarithmic pots like this one increase their resistance on a curve. At the halfway point volume will still be moderate, but it will increase sharply as you keep turning up the volume. This corresponds to how the human ear hears. Using a log pot therefore gives the effect that a setting of full volume on the control sounds twice as loud as a setting of half volume. A linear pot used as a volume control would give large apparent changes in loudness at low volume settings, with little apparent change over the rest of the control´s range.

Unlike some of our other potentiometers, this one is not breadboard-friendly. The pins are about 0.2" apart so it will fit into a breadboard, but the two rows are close together so you'd short the two halves. Thus, we suggest soldering wires to the pins as necessary, using these in a perf-board that doesn't have the rows connected, or designing a custom PCB.

Once you're done prototyping, you can drill a hole into your project box and mount the potentiometer using the included washer and hex nut. We've got plenty of matching T18-splined knobs that you can pair up.

Technical Details

  • 10K ohm potentiometer, log taper
  • 100,000 Cycle Life
  • 16mm Body
  • Rotational travel: 300°
  • Static Stop Strength: 90 oz-in
  • Rotational Torque: 0.5 to 1.25 oz-in

Product Dimensions: 26.5mm x 25.0mm x 17.0mm / 1.0" x 1.0" x 0.7"

Product Weight: 7.5g / 0.3oz

You may also like

-65%
Thumbnail 1Thumbnail 2

Short Flex Sensor

$7.70

$2.69

-65%
Thumbnail 1Thumbnail 2

SMD Component Testing Tweezers

$37.80

$13.23

Thumbnail 1Thumbnail 2

Micro Servo - High Powered, High Torque Metal Gear

$12.90

Thumbnail 1Thumbnail 2

Panavise Multi-Purpose Work Center (PV-350)

$145.20

-65%
Thumbnail 1Thumbnail 2

Replacement Tubes for Professional Silicone-Tip Solder Sucker (SS-02)

$2.20

$0.77

-65%
Thumbnail 1Thumbnail 2

Toggle Clamp - Small Flip-down Style

$3.80

$1.33

-65%
Thumbnail 1Thumbnail 2

Toggle Clamp - Medium Flip-up Style

$3.80

$1.33

-65%
Thumbnail 1Thumbnail 2

ST-Link STM8/STM32 v2 Compatible Programmer & Emulator

$14.40

$5.04

Thumbnail 1Thumbnail 2

Precision Straight Tweezers - Rhino SW-11

$12.00

-65%
Thumbnail 1Thumbnail 2

Waterproof DS18B20-Compatible Temperature Sensor with Resistor

$3.50

$1.22

Thumbnail 1Thumbnail 2

Rotary Encoder + Extras

$4.40

Thumbnail 1Thumbnail 2

Mini 2-wire Volt Meter (3.2 - 30 VDC)

$7.70